软件介绍

Serial Mac破解版软件优乐事分享的Mac os系统上一款现代化的终端设计,使与服务器,网络设备的工作,并为工程师和系统管理员嵌入式硬件更容易。内置从头开始为OS X,串行不再需要搜索并安装驱动程序,以便与大多数的USB转串口适配器和其他串口设备一起工作。
 

Serial for Mac破解软件功能介绍

其它强大功能包括完整的终端仿真,因此您可以使用屏幕为基础的方案包括的Emacs,vi或nano或导航需要配置网络设备的菜单。
 

Serial for Mac破解软件功能特色

•全功能的xterm,linux和ANSI / VT100终端仿真
•中断支持
•文本调整
•XMODEM,YMODEM,ZMODEM和Kermit文件传输
•手动或自动日志记录
•配置文件
•时间戳
•设备或内核驱动程序的仿真中断序列缺乏支持
•针对缺乏支持的设备或内核驱动程序的仿真XON / XOFF
 
串行包括对以下设备的内置支持:
•USB通信设备类(CDC)设备
•蓝牙串行端口配置文件(SPP)设备
•基于FTDI的USB至串行桥,Prolific,CH34x,SiLabs和TI芯片组
•FTDI的FT260 HID USB /串行桥
•SiLabs CP2110 HID USB /串行桥
•内置USB控制台端口的思科(和其他)设备
 

更新说明

Version 2.0.16:
– Support for macOS 14.0 (Sonoma)
– Other bug fixes and improvements.
 

Description

Serial is a modern terminal emulator designed to make working with servers, network equipment, and embedded hardware easier for engineers and system administrators.
 
For system administrators, Serial supports the all-important break sequence required when working with routers and switches. Serial also includes a full-featured terminal emulator, allowing you to work with the screen-based menus found in network equipment and Unix programs including the text editors vi and emacs.
 
Makers and engineers will appreciate Serial’s built-in support for embedded devices including the Arduino, Raspberry Pi, BeagleBone, and thousands of others. Serial includes several useful features for working with these devices including the ability to reset an Arduino, and the ability to connect to a BeagleBone over USB directly or through it’s on-board serial header.
 
Finally, Serial supports several of the most common USB to serial adapters without requiring drivers, often saving you the hassle of finding and installing additional software.

 

Serial Mac破解软件历史版

版本 下载 密码
2.0.15 立即下载 ssay
2.0.14 立即下载 ssay
2.0.13 立即下载 ssay
2.0.12 立即下载 ssay
2.0.10 立即下载 ssay
2.0.7 立即下载 ssay

发表回复

后才能评论

本站所有资源无论你是否注册成为本站的用户,都可以直接下载,且下载免费。

本站所有资源都是经过自己分期购的几台电脑,一一测试排查没问题才发布于大家分享,请放心下载!

最常见的情况是下载不完整: 可对比下载完压缩包的与网盘上的容量,若小于网盘提示的容量则是这个原因。这是浏览器下载的bug,建议用百度网盘软件或迅雷下载。 若排除这种情况,可在对应资源底部留言,或联络我们。

买新电脑第一件事就是打开电脑的任何来源,打开终端(command+空格 聚焦搜索:终端),复制以下命令粘贴到终端:sudo spctl --master-disable 然后按下回车键,出现钥匙图标后输入电脑的开机密码(输入过程中密码是看不到的)输入完成后再按下回车键即可 🔗详细图文教程:https://uleshi.com/mac_course-5.html